[Bio-Linux] phred/phrap/consed installation on Bio-linux
Keith Jolley
keith.jolley at medawar.ox.ac.uk
Fri May 5 11:32:51 EDT 2006
Your confusion stems from the fact that /usr/local/bioinf and /usr/software
are equivalent.
If you 'ls -l' from /usr you'll see that software is a symlink to
local/bioinf, so you could use either.
Keith
> -----Original Message-----
> From: bio-linux-bounces at envgen.nox.ac.uk [mailto:bio-linux-
> bounces at envgen.nox.ac.uk] On Behalf Of Jose A. Andres
> Sent: 05 May 2006 16:03
> To: Bio-Linux help and discussion
> Subject: Re: [Bio-Linux] phred/phrap/consed installation on Bio-linux
>
> Hi all,
>
> (Thanks in advance for all your help)
>
> I'd like to install phred/phrap/consed into bio-linux4 but since I am not
> funded by the NEBC, I have to do it from the original files I got from
> Phil's Green lab. I should be able to do it, but I am a bit confuse with
> the symlinks (and another couple of things) and I'd like to get some
> extra advice from the community (if possible).
>
> I realise how busy we all are and I'd really appreciate any suggestions
> and comments.THANKS!!
>
> Cheers,
>
> /Jose
>
> Here is what I am planning:
>
> # reading from a flash-drive...
>
> mount /media/usbkey
>
> # storing source code on /usr/local/src
>
> sudo mkdir -p /usr/local/src/phred
>
> #moving stuff around...
>
> sudo mv /media/usbkey/ /usr/local/src/phred
>
> #uncompressing the file ...
>
> uncompress phred-dist-020425.c-acd.tar.Z
> tar xvf phred-dist-020425.c-acd.tar
>
> # I've read somewhere (do not remember exactly where) that to compile
> phred with the correct optimization I need to edit one line of the make
> file
> (Soooo....
>
> nano Makefile ("remove # from the LXFLAGS = -DX86_GCC_LINUX line and
> save).
>
> #then...
>
> ./make
>
> #now I need to copy the executable of this version (to keep the bio-linux
> standards) into the right place. I am assuming
>
> /usr/software/phred/phred_020425). Am I right? or shall I put it into
> /usr/local/bioinf?? Sooo I create the new dir
>
>
> sudo mkdir -p /usr/software/phred/phred_020425 (or
>
> # and copy the executable there
>
> sudo cp phred /usr/software/phred/phred_020425
>
> # As I said I am a bit confuse cause both /usr/software and
> /usr/local/bioinf seem to have the same stuff in...
>
> !!!!!! Do I have to also copy the make the dir
> /usr/local/bioinf/phred/phred_02004425 and cp the Phred executable there?
>
> !!!!!! do I have to make a symlink? if so, shall I make it in the same
> place? That is
>
> sudo ln -s /usr/software/phred/phred_020425 /usr/software/phred/phred
>
> !!!!!!! or in the /usr/local/bioinf/ or both?
>
> sudo ln -s /usr/software/phred/phred_020425 /usr/local/bioinf/phred
>
> # Any suggestions?
>
> # I shall move the phred parameter file to the right location.Something
> like this?
>
> sudo cp phredpar.dat /usr/local/bioinf/phred/phred/prhredpar.dat
>
> #set the enviroment..
>
> nano -w /usr/local/bioinf/config_files/bioenvrc
>
> (Add and save..)
>
> export PHRED_PARAMETER_FILE=/usr/local/bioinf/phred/phred/phredpar.dat;
> export PATH=$PATH:/usr/local/bioinf/blast/blast:
> /usr/local/bioinf/netblast/netblast: /usr/local/bioinf/phred/phred:
> /usr/local/bioinf/phrap/phrap:/usr/sbin
>
> #installing
>
> WOULD THIS WORK??? IF so I shall also be able to install phrap and consed
> in a very similar way...
>
> THANKS EVERYONE!!!!!!!!!!!!!!!!!!
>
>
>
>
> _______________________________________________
> Bio-linux mailing list
> Bio-linux at envgen.nox.ac.uk
> http://envgen.nox.ac.uk/mailman/listinfo/bio-linux
More information about the Bio-linux-list
mailing list